Mosfets for Robotics

文章附图

MOSFET driver PCB with gate driver IC current sensing and power-stage componentsPower MOSFET package with gate drain source and exposed thermal pad

Product Overview

MOSFETs are power semiconductor devices used as high-speedelectronic switches in robotic power and motion-control systems. They controlthe flow of electrical energy from the battery or DC power bus to motors,actuators, converters and other high-current loads.

In a three-phase motor-drive system, six MOSFETs arecommonly arranged as three half-bridges. Controlled by a gate-driver IC, theyconvert DC input power into precisely regulated three-phase current for BLDCand PMSM motors.

Key Functions

  • Switches high voltage     and current at high speed

  • Controls power delivery     to motors and actuators

  • Forms half-bridge and     full-bridge power stages

  • Converts DC power into     three-phase motor current

  • Supports PWM speed and     torque regulation

  • Enables motor braking     and energy regeneration

  • Controls robot subsystem     power distribution

  • Supports DC-DC     power-conversion circuits

  • Reduces conduction and     switching losses

  • Improves system     efficiency and battery runtime

Typical Applications

  • Humanoid robot joints

  • Industrial robotic arms

  • Collaborative robots

  • AGV and AMR wheel drives    

  • BLDC and PMSM motor     controllers

  • Servo drives

  • Robot grippers and     linear actuators

  • Battery-protection and     power-distribution boards

  • DC-DC converters

  • Electronic load switches    

  • Pumps, fans and braking     systems

MOSFET Terminal Functions

Gate

The Gate receives the control signal from the Driver IC.Applying the required gate voltage turns the MOSFET on or off.

Drain

The Drain normally carries the main switched current. Inmany power packages, it is connected to the large exposed thermal padunderneath the device.

Source

The Source completes the main current path and oftenprovides the reference point for the gate-drive signal.

Exposed Thermal Pad

The large metal pad transfers heat from the MOSFET into thePCB copper area, thermal vias, heat spreader or robot chassis.

Main Components on the MOSFET Driver PCB

Power MOSFETs

Six N-channel MOSFETs form three half-bridges for athree-phase BLDC or PMSM motor. They are the main power-switching components.

Gate Driver IC

The Driver IC converts low-voltage PWM commands into fast,properly timed signals that switch the MOSFET gates.

Microcontroller or DSP

Executes motor-control algorithms, calculates the requiredphase currents and generates PWM control signals.

Gate Resistors

Control MOSFET switching speed and help reduce ringing,voltage overshoot and electromagnetic interference.

Bootstrap Capacitors

Provide the temporary voltage required to drive thehigh-side MOSFETs.

Current-Sense Resistors

Measure phase or DC-bus current for torque control, currentlimiting and short-circuit protection.

Current-Sense Amplifiers

Amplify the small voltage across the shunt resistors formeasurement by the controller.

DC-Link Capacitors

Stabilize the DC bus and supply transient current when themotor accelerates or changes load.

TVS Diode and Fuse

Protect the driver board against voltage spikes, excessivecurrent and short-circuit conditions.

CAN Transceiver

Receives commands from the robot’s main controller andtransmits operating data and fault information.

Encoder or Hall-Sensor Interface

Receives rotor-position and speed feedback for closed-loopmotor control.

Heat Spreader

Conducts heat away from the MOSFET power stage and helpsmaintain reliable continuous operation.

How It Works

The robot’s main controller sends a motion command to themotor-control MCU. The MCU calculates the required motor phase currents andproduces PWM signals.

The Driver IC amplifies these signals and switches the sixMOSFETs in a controlled sequence. The MOSFET bridge converts DC battery powerinto three-phase current for the motor. Current sensors and position sensorsreturn real-time feedback so that the controller can continuously adjust speed,position and torque.

Typical Power and Signal Flow

Battery or DC Bus → MOSFET Three-PhaseBridge → Motor

Main Controller → MCU → Driver IC →MOSFET Gates

Current and Position Feedback → MCU →Real-Time Adjustment

Common MOSFET Types

MOSFET   type

Typical   use

N-Channel MOSFET

Motor drives, converters and  high-current switching

P-Channel MOSFET

Reverse-polarity protection and  high-side load switching

Logic-Level MOSFET

Direct or low-voltage  gate-drive applications

Low-RDS(on) MOSFET

High-current systems requiring  low conduction losses

High-Voltage MOSFET

Higher-voltage power supplies  and industrial drives

Automotive-Grade MOSFET

High-reliability motion and  power-control systems

Dual MOSFET

Compact half-bridge and  load-switch circuits

Integrated Power Stage

Combines MOSFETs and driver  circuitry in one package

Key Benefits

  • High-speed switching

  • Low conduction     resistance

  • High current-handling     capability

  • Efficient motor and     power control

  • Compact surface-mount     packages

  • Fast PWM response

  • Improved battery     efficiency

  • Scalable for different     motor power levels

Selection Parameters

When selecting a MOSFET, consider:

  • Drain-source voltage:     VDS

  • Continuous and pulsed     drain current

  • On-resistance: RDS(on)

  • Gate-charge requirements    

  • Threshold and     recommended gate-drive voltage

  • Switching speed and     operating frequency

  • Power dissipation

  • Package type and PCB     footprint

  • Thermal resistance

  • Safe Operating Area—SOA

  • Avalanche-energy     capability

  • Body-diode     characteristics

  • Operating-temperature     range

  • Industrial or automotive     qualification

Short Product Description

Antfieldpower MOSFET solutions deliver efficient high-speed switching for robotic motordrives, joint actuators, power converters and battery-management systems.Low-resistance packages and optimized thermal performance help improve controlaccuracy, energy efficiency and system reliability.

Global Product Inquiry
Custom PCB Fabrication, PCBA Assembly & Component Procurement Solution
Inheriting the Ant Spirit, Building Core Competitiveness in Electronic Supply Chain with Professionalism & Dedication.
PRODUCT
CONTACT
+86-13902944251 judy@atftek.com