Driver ICs for Robotics

文章附图

Robot motor driver PCB with gate driver IC and power MOSFET stageThree-phase motor driver IC circuit for BLDC and PMSM robotic motors

Product Overview

Driver ICs are semiconductor devices that convert low-powercontrol signals from an MCU, DSP or FPGA into the electrical signals requiredto operate motors, MOSFETs, relays, solenoids, LEDs and other loads.

In robotic motion-control systems, motor-driver andgate-driver ICs control external power MOSFETs to regulate motor current,speed, torque and direction. They are widely used in BLDC, PMSM, brushed DC andstepper-motor systems.

Key Functions

  • Amplifies low-power     control signals

  • Drives internal or     external power MOSFETs

  • Controls motor speed,     torque and direction

  • Generates PWM and     gate-drive signals

  • Supports three-phase     motor commutation

  • Measures or regulates     motor current

  • Enables braking and     regenerative operation

  • Detects undervoltage,     overcurrent and overheating

  • Reports operating status     and fault conditions

  • Supports closed-loop     position, speed and torque control

Typical Applications

  • Humanoid robot joints

  • Industrial robotic arms

  • Collaborative robots

  • AGV and AMR wheel drives    

  • Robot grippers and end     effectors

  • Service and delivery     robots

  • Robot dogs

  • Pumps, fans and linear     actuators

  • Gimbal and     camera-positioning systems

  • Precision servo-control     systems

Common Driver IC Types

Driver   IC type

Main   function

Gate Driver IC

Drives external MOSFETs or  IGBTs

Three-Phase Motor Driver

Controls BLDC and PMSM motors

Brushed DC Motor Driver

Controls motor direction, speed  and braking

Stepper Motor Driver

Controls stepper-motor phase  current and position

Integrated Motor Driver

Combines control circuits and  power transistors

Solenoid Driver

Controls valves, brakes and  electromagnetic actuators

High-Side/Low-Side Driver

Controls power switches  connected to different supply rails

Half-Bridge/Full-Bridge Driver

Forms bidirectional motor and  actuator power stages

Main Components on the Driver PCB

Driver IC

The Driver IC receives PWM, enable and direction commandsfrom the controller. It generates the properly timed gate-drive signalsrequired by the MOSFET power stage.

Power MOSFETs

Six MOSFETs typically form three half-bridges in athree-phase motor drive. They switch the DC supply into controlled three-phaseoutputs for the motor.

Microcontroller or DSP

Executes motor-control algorithms such as six-stepcommutation, sinusoidal control or field-oriented control—FOC.

Current-Sense Resistors

Low-resistance shunts measure phase or bus current,supporting torque control, current limiting and fault protection.

Current-Sense Amplifiers

Amplify the small voltage across the current-senseresistors so that the controller can accurately measure motor current.

DC-Link Capacitors

Stabilize the DC bus, reduce voltage ripple and providetransient current during motor acceleration.

Bootstrap Capacitors

Provide the temporary gate-drive voltage required to switchhigh-side MOSFETs.

Gate Resistors

Control MOSFET switching speed, reduce ringing and helpmanage electromagnetic interference.

Encoder or Hall-Sensor Interface

Receives rotor-position feedback for commutation andclosed-loop position, speed or torque control.

CAN Transceiver

Connects the joint driver to the robot’s main controllerfor commands, telemetry and fault reporting.

TVS Diode and Fuse

Protect the board against voltage spikes, short circuitsand excessive current.

Heat Spreader

Transfers heat away from the Driver IC and MOSFETs tosupport continuous high-current operation.

How It Works

The robot’s main controller sends motion commands to themotor-control MCU through CAN or another communication interface. The MCUcalculates the required phase currents and generates PWM commands.

The Driver IC converts these logic-level signals intohigh-current gate-drive signals. The MOSFET bridge then supplies controlledthree-phase power to the motor. Encoder, Hall-sensor and current-sensingsignals are returned to the controller, forming a closed-loop control system.

Typical Signal Flow

Main Controller → Motor-Control MCU →Driver IC → MOSFET Bridge → Motor

Encoder/Hall Sensor + Current Feedback →MCU → Real-Time Adjustment

Protection Functions

Depending on the selected device, Driver ICs may provide:

  • Undervoltage lockout

  • Overcurrent protection

  • Short-circuit protection    

  • Shoot-through prevention    

  • Dead-time control

  • Gate-drive fault     detection

  • Overtemperature shutdown    

  • Motor-stall detection

  • Open-load detection

  • Fault-status output

Selection Parameters

When selecting a Driver IC, consider:

  • Motor type

  • DC bus voltage

  • Peak and continuous     motor current

  • Integrated or external     MOSFET architecture

  • Number of half-bridge     channels

  • Gate-drive source and     sink current

  • PWM frequency

  • Control method and     interface

  • Current-sensing     architecture

  • Encoder or Hall-sensor     compatibility

  • Protection functions

  • Package and thermal     resistance

  • Operating-temperature     range

  • Functional-safety     requirements

  • Industrial or automotive     qualification

Short Product Description

AntfieldDriver IC solutions provide precise and reliable control for robotic motors,actuators and power switches. Supporting BLDC, PMSM, brushed DC andstepper-motor applications, these devices enable efficient gate driving,current regulation, motion control and system protection.

SEO Meta Description

ExploreAntfield Driver IC solutions for robotic motor control, gate driving, jointactuation and motion systems, with customized PCB, PCBA and component-sourcingsupport.


Global Product Inquiry
Custom PCB Fabrication, PCBA Assembly & Component Procurement Solution
Inheriting the Ant Spirit, Building Core Competitiveness in Electronic Supply Chain with Professionalism & Dedication.
PRODUCT
CONTACT
+86-13902944251 judy@atftek.com