Memory for Robotics

文章附图

memory1.pngmemory2.png

Product Overview

Memory is a fundamental part of a robot’s control andcomputing system. It stores firmware, operating systems, AI models,configuration parameters and application data, while also providing theprocessor with fast access to real-time sensor and control information.

Depending on the system requirements, robotic computingplatforms may use DDR or LPDDR as working memory, NOR Flash for boot code, eMMCor NAND Flash for program and data storage, and EEPROM or FRAM for calibrationparameters and system settings.

Key Functions

  • Stores robot firmware,     operating systems and application programs

  • Provides high-speed     working memory for CPUs, MCUs, GPUs and FPGAs

  • Loads and stores AI     models, navigation maps and motion algorithms

  • Buffers camera frames,     sensor data and communication packets

  • Retains calibration     data, configuration parameters and equipment IDs

  • Records operating logs,     fault information and maintenance data

  • Supports firmware     updates and system recovery

Memory Types

Memory   type

Main   function

DDR / LPDDR

High-speed volatile working  memory for processors and AI computing

SRAM

Low-latency memory for cache,  data buffers and real-time control

NOR Flash

Stores bootloaders, firmware  and executable code

NAND Flash

Provides higher-capacity  non-volatile data storage

eMMC / UFS

Integrated storage for  operating systems, applications, maps and AI models

EEPROM

Stores configuration,  calibration and identification data

FRAM

High-endurance storage for  frequently updated parameters and event records

Typical Applications

  • Humanoid robots

  • Industrial robotic arms

  • Autonomous mobile robots     and AGVs

  • Robot vision and AI     computing systems

  • Motion-control systems

  • Navigation and mapping     controllers

  • Edge-computing platforms    

  • Service and inspection     robots

  • Data-logging and     predictive-maintenance systems

Main Components on the Computing PCB

Memory ICs

DDR or LPDDR devices provide the processor withhigh-bandwidth working memory. They are normally positioned close to theprocessor to minimize signal-path length and improve signal integrity.

Processor / SoC

The CPU, MCU, GPU, FPGA or SoC executes the robot’s controlsoftware and exchanges data continuously with the memory devices.

eMMC or NAND Flash

Provides non-volatile storage for the operating system,application software, AI models, navigation maps, images and operating records.

NOR Flash

Typically stores the bootloader, startup firmware andrecovery program required when the robot powers on.

EEPROM or FRAM

Used for smaller amounts of persistent data, includingcalibration values, product information, operating parameters and faultrecords.

Power-Management IC

The PMIC, DC-DC converters and LDO regulators generate thedifferent supply voltages required by the processor and memory devices.

Clock and Oscillator

Provides the timing reference required for processoroperation and high-speed memory-data transfer.

Capacitors and Resistors

Decoupling capacitors stabilize the memory power supply.Termination resistors help maintain signal quality on high-speed memory buses.

Connectors and Protection Components

Board-to-board connectors connect the computing board tocameras, sensors, motors and communication modules. ESD and surge-protectioncomponents help protect external interfaces.

How It Works

When the robot starts, the processor reads the boot programfrom NOR Flash or eMMC. The operating system, control software and AI modelsare then loaded into DDR or LPDDR memory for high-speed execution.

During operation, sensor measurements, camera images,navigation data and motor-control information are temporarily buffered inworking memory. Important settings, calibration values and operating logs aresaved in non-volatile memory so that they remain available after power isremoved.

Selection Parameters

When selecting memory for a robotic computing system,consider:

  • Memory technology and     capacity

  • Interface and     data-transfer rate

  • Bus width and latency

  • Operating voltage

  • Package type and PCB     footprint

  • Industrial     operating-temperature range

  • Data-retention period

  • Program/erase endurance

  • ECC support

  • Power consumption

  • Processor compatibility

  • Product lifecycle and     supply continuity

  • Automotive or industrial     qualification requirements

Short Product Description

Antfieldrobotics memory solutions provide reliable program storage, high-speed dataaccess and real-time buffering for robotic control and computing platforms.Available memory technologies include DDR, LPDDR, SRAM, NOR Flash, NAND Flash,eMMC, EEPROM and FRAM for applications ranging from firmware storage to AIinference and sensor-data processing.

Global Product Inquiry
Custom PCB Fabrication, PCBA Assembly & Component Procurement Solution
Inheriting the Ant Spirit, Building Core Competitiveness in Electronic Supply Chain with Professionalism & Dedication.
PRODUCT
CONTACT
+86-13902944251 judy@atftek.com