Battery Packs for Robotics
Product OverviewRobot battery packs are rechargeable energy-storage systemsdesigned to supply reliable DC power to robotic computing, sensing,communication and motion-control subsystems. A complete battery pack typically integrates lithium-ioncells, a Battery Management System (BMS), current and temperature monitoring,balancing circuits, protection devices, high-current connectors and amechanically protected enclosure. Unlike a standard electronic component soldered directlyonto a PCB, a robotic battery is usually manufactured as an independent module.Its BMS PCB is installed inside the battery enclosure and connected to thecells, power bus and communication interface. Key Functions
Typical Applications
Main Parts of the Battery PackLithium-Ion CellsThe cells are the primary energy-storage components. Theymay use cylindrical, prismatic or pouch construction depending on capacity,space, weight and power requirements. Cell Holders and Compression StructureFlame-retardant holders, spacers and compression framesmaintain cell alignment, prevent mechanical movement and improve resistance tovibration and shock. BusbarsNickel-plated copper or other conductive busbars connectthe cells in series and parallel to obtain the required pack voltage andcapacity. Insulation SystemInsulating sheets, terminal covers, barriers and sleevesprevent unintended electrical contact and help separate high-current conductorsfrom the enclosure. Temperature SensorsNTC thermistors or other sensors monitor the temperature ofcells, busbars and power components. EnclosureThe enclosure protects the cells and electronics fromimpact, dust, moisture and mechanical damage. It may also incorporate rails,latches, shock absorbers and pressure-relief features. Power and Communication ConnectorsThe high-current connector transfers energy to the robot. Aseparate low-voltage connector normally carries CAN, SMBus, UART or other BMScommunication signals. Main Components on the BMS PCBBattery-Monitoring IC / AFEThe Analog Front End measures individual cell voltages andmonitors pack conditions. It is one of the main components of the BMS. MicrocontrollerThe MCU processes measurements, estimates battery status,controls protection functions and communicates with the robot controller. Balancing ResistorsThese resistors discharge cells with slightly highervoltage, helping maintain a more consistent state of charge across the batterypack. Protection MOSFETsBack-to-back MOSFETs can disconnect the charge or dischargepath when an overvoltage, undervoltage, overcurrent or short-circuit conditionis detected. Current-Shunt ResistorThe shunt creates a small voltage proportional to packcurrent, allowing the BMS to measure charge and discharge current. Current-Sense AmplifierAmplifies the shunt voltage for accurate currentmeasurement and protection. FuseProvides irreversible protection against severe overcurrentor short-circuit conditions. Contactor or Relay DriverControls a relay or DC contactor used to connect anddisconnect the main battery output in higher-power systems. Pre-Charge CircuitA pre-charge resistor and switching device limit inrushcurrent when the battery is connected to large capacitive loads such as motordrives. DC-DC ConverterGenerates the low-voltage supply required by the monitoringIC, MCU and communication circuit. CAN TransceiverTransfers state of charge, voltage, current, temperature,alarms and diagnostic data between the BMS and robot controller. Service DisconnectAllows the high-voltage or high-current battery path to besafely interrupted during maintenance and transportation. How It WorksCells are connected in series to increase voltage and inparallel to increase capacity and current capability. The BMS continuouslymeasures cell voltage, pack current and temperature. If all conditions are within the permitted range, theprotection circuit allows energy to flow to the robot’s power-distributionsystem. If an abnormal condition is detected, the BMS can reduce availablepower, issue a warning or disconnect the battery output. Typical Energy FlowBattery Cells → BMS Protection →Fuse/Contactor → Power Distribution → Computing, Sensors and Motor Drives Typical Communication FlowCell and Temperature Sensors → BMS AFE →MCU → CAN Interface → Robot Main Controller Common Battery Types
Key Benefits
Selection ParametersWhen selecting a robot battery pack, consider:
Design and Safety Considerations
Short Product DescriptionAntfieldrobotic battery solutions provide reliable energy storage, high-current powerdelivery and intelligent battery management for mobile and autonomous roboticsystems. Integrated BMS protection, cell monitoring, balancing andcommunication help improve operating safety, battery life and systemreliability.
|





